Technical guide

GEZE Door Closers for Aluminium Doors: Selection and Adjustment

A well-specified door closer brings an aluminium door back to its closed position smoothly and reliably. This guide compares selected GEZE models and explains how to coordinate closing force, mounting, accessibility and fire-door functions before ordering.

Alumproof · Technical resources · 6 min read

On this page
  1. What to establish before choosing a closer
  2. Four GEZE options to compare
  3. Coordinate the closer with the aluminium profile
  4. Understand the main adjustments
  5. Accessibility and reliable closing
  6. Fire doors, hold-open systems and double doors
  7. Commissioning and common symptoms
  8. Prepare a closer specification with Alumproof
  9. Related technical guides

Start with the complete door. The closer, guide rail, hinges, seals, lock and aluminium profile must work together. A model name or maximum leaf width is only the starting point for a specification.

What to establish before choosing a closer

Prepare a short door schedule for each opening. A sheltered internal door and an exposed entrance may need different arrangements even when their dimensions are similar. Record:

  • Door geometry: leaf width, height, mass, opening direction and required opening angle.
  • Construction: aluminium system, profile sections, reinforcement and available space for the closer and guide rail.
  • Use: expected traffic, users, opening effort, time needed for passage and any access-control equipment.
  • Environment: wind exposure, draughts and pressure differences created by ventilation.
  • Required functions: fire or smoke protection, closing sequence on double doors, and whether an approved hold-open arrangement is needed.

Include the proposed installation position in the enquiry: on the leaf or frame, on the hinge side or opposite side. Different mounting arrangements can require different closer variants, rails, brackets or plates. Ask the door supplier to confirm the complete combination against the current GEZE installation drawings.

Four GEZE options to compare

The following figures refer to the specific versions named below. They are manufacturer limits for initial comparison, rather than confirmation that a model suits every door within that width. Check all installation and application conditions for the final assembly.

On smaller screens, scroll the comparison sideways to read all four columns.

Selected GEZE door closer models and published limits
ModelEN closing forceMaximum leaf widthSelection point
TS 3000 EN 3EN 3, fixed950 mmSurface-mounted closer with guide rail. Confirm that the fixed power size matches the application.
TS 5000EN 2–6, adjustable1,400 mmSurface-mounted guide-rail model with adjustable closing force, closing speed, latching action and backcheck.
TS 5000 EClineEN 3–5, adjustable1,250 mmGuide-rail system with opening assistance. Assess it where ease of manual opening is a key part of the brief.
Boxer 2–4EN 2–4, adjustable1,100 mmConcealed installation. GEZE lists a maximum leaf mass of 130 kg and a minimum leaf thickness of 40 mm for this version.

For the TS 5000 ECline, specify the complete closer and opening-assistance rail combination. An ECline closer body alone does not describe the complete operating arrangement. The GEZE ECline technical data should be read alongside the selected rail documentation.

For Boxer 2–4, the published minimum thickness does not establish compatibility with an aluminium profile. Check the available internal chamber, machining, reinforcement, hinge geometry and access for adjustment. Other Boxer versions have different limits; do not transfer their ratings to the 2–4 model.

Coordinate the closer with the aluminium profile

Confirm the fixing detail before fabrication. The drawing should identify the closer and rail position, approved fasteners, reinforcement or mounting plates, and clearances to the frame, glazing beads and adjacent finishes. For concealed hardware, include the machining drawing and the space needed to remove or service the components.

Ask the aluminium system supplier to review any proposed machining near a thermal break, drainage route or seal. Also check that the closer arm and rail can move through the required opening angle without contacting a wall, reveal or other fitting. Resolve these details in the shop drawings rather than leaving them to site adjustment.

Understand the main adjustments

The available controls depend on the model. These terms describe different functions:

  • Closing force: the power that returns the door towards the closed position; usually expressed as an EN size.
  • Closing speed: the rate of movement during the closing cycle.
  • Latching action: control of the final part of closing as the door engages the latch.
  • Backcheck: resistance that cushions the door during opening.

Use the instructions for the exact closer and mounting arrangement. Valve locations and adjustment ranges vary. GEZE’s door closer adjustment guidance explains the functions and common symptoms; final adjustment should be carried out by a competent installer.

Accessibility and reliable closing

A door must be manageable for its intended users and still close as required. Review the complete route through the entrance: approach space, clear passage, handle position, opening effort and time available to pass through.

GEZE presents ECline as an option for easier manual opening, but the closer name alone does not demonstrate that the finished entrance meets the project’s accessibility requirements. Have opening effort and closing performance checked on the installed assembly. Where manual operation is unsuitable, ask the designer and supplier to review an appropriate assisted or automatic solution.

For the wider design brief, see Door Closers and Accessible Use.

Fire doors, hold-open systems and double doors

For a fire or smoke door, confirm that the exact closer, mounting arrangement and accessories are covered by the door assembly’s supporting documentation. A closer’s fire-door suitability does not approve every possible installation.

A fire door that needs to remain open during normal use requires a suitable approved hold-open system that releases the door when required. Do not use a wedge or an ordinary mechanical hold-open device. GEZE’s hold-open system guidance describes the coordinated role of detection, release, power supply and holding equipment. Confirm the configuration, inspection and maintenance requirements for the project location.

On rebated double doors, the leaves must close in the correct order. A closing sequence control coordinates the active and inactive leaves; two independent closers do not provide that function by themselves. GEZE’s TS 4000 E-IS documentation illustrates this principle. Select the actual system for the specified door assembly.

Commissioning and common symptoms

Complete the functional checks after the hinges, seals, lock and access-control components are installed. Test closing from several opening positions, latch engagement, user passage and any release or sequence-control functions. Record the component references and hand over the operating and maintenance instructions.

  • Door does not latch: check alignment, seals and latch resistance before increasing force.
  • Door slams: check speed, latching settings, draughts and possible oil leakage.
  • Door is hard to open: investigate hinges, seals, pressure differences and the selected power size together.

These are diagnostic starting points from GEZE’s adjustment guidance. Oil leakage or damaged controls require professional assessment, rather than further adjustment.

Prepare a closer specification with Alumproof

Send the door schedule, profile system, leaf dimensions and mass, opening direction, project location and required functions. Include any fire, accessibility or access-control requirements so that the hardware arrangement can be reviewed as part of the complete aluminium door.

Discuss your door specification →

Related technical guides

All technical guides · Explore aluminium door systems

Published by Alumproof. Manufacturer information checked on 16 October 2026 using the official GEZE references linked above. This guide supports specification planning; the current installation instructions and documentation for the selected door assembly govern the final configuration. GEZE product references do not imply endorsement or certification of Alumproof.