Schüco ADS 50.NI – Aluminium doors

Schüco ADS 50.NI Aluminium Door System for professional architectural projects. Key published data include maximum height 2500 mm; maximum width 1100 mm; maximum glazing or panel thickness 32 mm. Final values depend on configuration.

Category: Brand:
Certified quality systems
Non-thermally insulated system
Reliable project delivery support

Description

Schüco ADS 50.NI Aluminium Door System

Schüco ADS 50.NI is a Schüco aluminium door system developed for professional entrance and door construction. Alumproof provides system selection, feasibility review, detailed coordination, production documentation, CNC fabrication, assembly, glazing and project logistics. The configuration is selected for the actual element sizes, architectural intent, required performance and installation conditions.

Schüco ADS 50.NI is the primary system reference used throughout this product specification.

The practical quality of Schüco ADS 50.NI is decided during coordination: system limits, visual proportions, hardware, glazing, drainage and fixings must support the same design intent. Alumproof connects those decisions directly with fabrication.

Schüco ADS 50.NI Technical Data

The following values originate from the referenced Schüco product information. They may describe maximum dimensions, best values or particular tested arrangements and must not be interpreted as simultaneous performance for every element.

Maximum height 2500 mm
Maximum width 1100 mm
Maximum glazing or panel thickness 32 mm
Maximum vent weight 200 kg
Area of application Interior use, exterior use, commercial projects
Air permeability Class 2
Watertightness E 1500
Wind-load resistance Class C3
Burglar resistance Up to RC 2

What the Published Values Mean for the Project

The published maximum height of 2500 mm describes a system limit rather than an automatic design allowance. Proportions, loads, infill weight, hardware and exposure determine whether that size is feasible.

The published maximum width of 1100 mm describes a system limit rather than an automatic design allowance. Proportions, loads, infill weight, hardware and exposure determine whether that size is feasible.

The maximum glazing or panel thickness of 32 mm defines an important compatibility limit. Glass build-up, edge cover, weight, safety class, coating position and gasket selection must all be checked together.

The stated maximum vent weight of 200 kg is relevant only with the appropriate hardware, geometry and support conditions. Operating forces, transport and installation method may impose a lower project limit.

Key Design Considerations

  • Maximum height: 2500 mm.
  • Maximum width: 1100 mm.
  • Maximum glazing or panel thickness: 32 mm.
  • Maximum vent weight: 200 kg.
  • Area of application: Interior use, exterior use, commercial projects.
  • Air permeability: Class 2.
  • Watertightness: E 1500.
  • Wind-load resistance: Class C3.
  • Burglar resistance: Up to RC 2.
  • Configuration: profiles, glazing or infill, hardware and interfaces are selected as one coordinated system.
  • Verification: final dimensions and performance are checked for the actual project arrangement.
  • Documentation: approved details are transferred into production and installation information.

Design, Performance and Application

Schüco ADS 50.NI is defined by much more than the frame profile. Opening direction, leaf size, threshold, infill, hinges, locks, closers, handles and access-control components form one operational assembly. Alumproof coordinates these elements around the intended use, whether the requirement is a residential entrance, a frequently operated commercial door or a glazed door integrated into a façade.

Door dimensions and weight must be checked against the selected hinge and hardware configuration. The choice between glass and panel infill affects thermal behaviour, stiffness and appearance. Threshold construction influences weather resistance and accessibility, while the fixing arrangement must transfer operating and wind loads into the surrounding structure without distorting the frame. These issues are resolved before machining and assembly.

Published thermal, air, water, wind, acoustic or security classifications apply to specific tested combinations of profiles, seals, infill and hardware. A change to leaf dimensions, lock preparation, threshold or glazing can alter the declared result. Alumproof therefore verifies which performance claims are relevant to the proposed door and avoids extending a classification beyond the manufacturer-approved configuration.

Interface drawings show the head, jamb and threshold zones, including membranes, insulation continuity, drainage and floor build-up. For access-controlled entrances, cable routes, lock type, door loop and power requirements are coordinated with the electrical designer. Finish, colour, visible hardware and panel geometry are reviewed together so that the final construction remains technically coherent and visually consistent.

Glazing, Infill and Interfaces

Glazing or opaque infill is selected for safety, thermal, acoustic, structural and visual requirements. The nominal capacity of a profile does not by itself confirm that a proposed glass build-up is suitable. Alumproof checks thickness, weight, edge cover, support, compatibility with gaskets and sealants, and the influence of the infill on the element hardware and frame. Where panels, back pans, membranes or insulation are included, their interfaces are documented as part of the complete construction.

Connections to concrete, steel, timber, roofing, insulation, waterproofing and internal finishes are developed around the actual opening and substrate. Particular attention is given to fixing access, edge distances, drainage paths, membrane continuity, movement, tolerances and replaceability. These details help preserve the intended performance of Schüco ADS 50.NI after the element leaves the factory.

From Drawings to Production

Before Schüco ADS 50.NI reaches production, the key decisions are visible in coordinated drawings: element references, profile zones, infill, opening direction, drainage, fixings and interfaces. This reduces ambiguity for procurement, CNC machining, assembly and site installation.

Alumproof reviews drawings, elevations, schedules and specifications before preparing production documentation. The review covers dimensions, opening logic, profile selection, component availability, machining access, hardware positions, drainage, glazing sequence, transport size and installation access. Questions that can affect cost or feasibility are raised before fabrication rather than being transferred to the construction site.

Approved profiles are cut and CNC-machined according to the production information. Assembly and glazing follow the selected system configuration, with checks appropriate to the product type and agreed quality plan. Finished elements are identified, protected and packed for coordinated delivery. Installation responsibilities, lifting conditions and site tolerances should be confirmed separately for each project.

Why Specify Schüco ADS 50.NI Through Alumproof?

Alumproof combines architectural understanding with practical aluminium fabrication. This makes it possible to compare system variants, identify dimensional or interface risks, develop buildable details and maintain a direct connection between approved drawings and production. The objective is a technically coherent result that supports the architecture and can be manufactured, transported, installed and maintained as planned.

Related Alumproof Resources

Important System Note

All technical values, classifications and dimensional limits must be verified for the final Schüco ADS 50.NI configuration. Actual performance depends on element size and proportions, selected profile variant, glazing or panel, hardware, seals, drainage, reinforcement, fixings, installation substrate and workmanship. A value published for one tested specimen or best-performing configuration must not be applied unconditionally to another construction.

Send your drawings, elevations, schedules or specification to Alumproof for a technical review and project quotation.